Plate Tectonics
Plate Tectonics

This free course is available to start right now. Review the full course description and key learning outcomes and create an account and enrol if you want a free statement of participation.

Free course

Plate Tectonics

4.3 Plate motion on a spherical Earth

Earth's tectonic plates are continuously in motion with respect to each other, and together they form the closed surface of a sphere (i.e. the Earth's surface). Understanding the movement of plates, therefore, requires a geometrical analysis of motions over a spherical surface. This is described in the Euler (pronounced 'oiler') geometrical theorem, which shows that every displacement of a plate from one position to another on the Earth's surface can be regarded as a simple rotation of that plate about a suitably chosen axis, known as an Euler pole or pole of rotation, which passes through the centre of the Earth.

Plate movement on a spherical Earth is illustrated in Figure 26. Two plates, A and B, are separating at a constructive plate boundary and rotating about a pole of rotation (which in this case is the North Pole). The constructive plate boundaries lie along lines of longitude, whereas the transform faults are parallel to lines of latitude. Lines of longitude are great circles with centres that coincide with the centre of the Earth; lines of latitude, which are at right angles to lines of longitude, are small circles with centres displaced from the Earth's centre. When the plates separate, the gap between them increases but, quite obviously, they separate a smaller amount close to the North Pole than at the Equator.

Figure 26
Figure 26 (a) The geometry of a constructive boundary in which two plates are separating. (b) The geometrical relationships that may be used to describe plate movement. Note that whilst the rotation angle remains the same along the length of the split, the width of the gap increases with angular distance from the pole of rotation (in this case the North Pole).

Question 21

What effect does this have on local full and half spreading rates along the length of the constructive plate boundary?

Answer

Spreading rates measured close to the pole of rotation will be small while those further away will be much greater.

This aspect of spherical geometry explains why relative plate motions expressed simply in terms of mm y−1 vary along the length of a plate margin. Needless to say, poles of rotation are not all located at the geographical poles but can fall anywhere on the Earth's surface. For example, the Mid-Atlantic Ridge has variable spreading rates along its length, with values of 37-40 mm y−1 in the South Atlantic, to lower values of 23-26 mm y−1 in the North Atlantic (Figure 8).

Question 22

What do these variations in spreading rate tell you about the location of the pole of rotation of the South American Plate?

Answer

Spreading rates are lower in the North Atlantic and so the pole of rotation must be located somewhere in the northernmost Atlantic Ocean.

The location of the pole of rotation can be determined more accurately from the orientation of the transform faults that cut the Mid-Atlantic Ridge. Transform faults lie along small circles and, by definition, lines at right angles to them will pass through the pole of rotation (Figure 27a). Using this method, the pole of rotation of the South Atlantic Plate can be shown to be located in the North Atlantic, south of Greenland (Figure 27b).

Figure 27
Figure 27 (a) Transform faults (dashed lines) in the equatorial region of the Atlantic Ocean compared with small circles (solid lines) concentric about a rotation pole at 58°N, 36°W. (b) Great circles drawn perpendicular to the transform faults that offset the Atlantic spreading ridge. The great circles converge on an area in the North Atlantic, defining the general position of the pole of rotation of the plate.

Finally, some plates have an internal pole of rotation that results in some complex consequences for relative plate motions. The first, and possibly most obvious, is that the real motion of the plate becomes one of rotation. The African Plate (Figure 25) is a good example. The southern part of the African Plate is moving to the east while the northern part is moving to the west - the plate is rotating anticlockwise about a pole located somewhere near the Canary Islands, off the northwest coast of Africa. The second consequence is that an internal pole can lead to a given plate boundary transforming from a constructive plate boundary through a conservative plate boundary to a destructive plate boundary along its length, although this is not apparent around the African Plate.

S279_1

Take your learning further

Making the decision to study can be a big step, which is why you'll want a trusted University. The Open University has 50 years’ experience delivering flexible learning and 170,000 students are studying with us right now. Take a look at all Open University courses.

If you are new to university level study, find out more about the types of qualifications we offer, including our entry level Access courses and Certificates.

Not ready for University study then browse over 900 free courses on OpenLearn and sign up to our newsletter to hear about new free courses as they are released.

Every year, thousands of students decide to study with The Open University. With over 120 qualifications, we’ve got the right course for you.

Request an Open University prospectus